I didn't see you state which model of QNAP you have? Most QNAPS have a small recessed reset button in back you access with a paperclip. Try doing a basic reset on your QNAP, which will reset all of your settings to DHCP (hold in reset button about 3 seconds or till it beeps once). Seems it's retaining some IP config assignments in use from your old router. If your QNAP says it has an IP address of 192.168.1.x, there's your issue, since Eeros default to 192.168.7.x, and for any device to be usable it must match the Eero's gateway and IP range. ![]() I have several QNAPS that I use with Mac computers, and this clearly sounds like an IP or DNS issue. Your machine will always consult a local HOSTS file first before attempting to use a DNS entry to resolve a server name to an IP address.Īgain, this is techie stuff but unfortunately important to know because unfortunately networking is almost never a plug-and-play affair anymore. One last suggestion is that once you set your NAS up to use a static IP address consistent with your DHCP configuration (the same first 3 numbers in the IP address scheme), you could edit your local HOSTS file on your PC to add an entry for the NAS. The ".local" part is apparently important for Mac. So something like afp://192.168.1.50/your_share (for Apple) might give you more success, avoiding local DNS issues altogether.Īlso, if you want to use server names instead of IP addresses, try afp://yourNAS.local/your_share. ![]() Net/net, I think it might be worthwhile to look into setting up a static IP address for your NAS, and always hitting it from your computers using the IP address rather than by NAS 'name'. You might also look into configuring your NAS to be the 'master browser' on your network (you'll have to google this one) to resolve DNS issues. Regarding Apple computers networking issues, in the realm of 'tweaking-techie' things might be to change the version of SMB that your NAS device uses - SMB 3.0 is the latest standard but people have reported better compatibility with Apple products by lowering the SMB level used in the NAS to SMB 2.0 or even 1. 100 for static assignments, for things like my printer (which definitely prefers a static assignment) and my NAS. And in my network I have all DHCP assignments starting at 192.168.1.100, reserving everything below. When I setup my eero, I found the 'advanced' setting to configure the DHCP range to start with 192.168.1.0, which is what my static-IP-configured NAS was expecting and consistent with how I am used to accessing my home network. While people are always saying AFP (Apple's own legacy networking protocol) is "on its way out", I've found it still the most reliable way of connecting to a NAS with a Mac computer. In my case it had to do with the SMB implementation Apple uses, it's non-standard/proprietary, so rather than using the standard libraries everyone else does, they rolled their own. If you are using windows 10, try make sure that network discovery is enabled.For what it's worth, although I don't have a QNAP, I do have a Synology NAS and had similar issues with accessing it from my Mac computers (Windows PC's were OK). can try replacing it, but i suspect the issue in this case is something else.Īre you by chance running your pc client in a non admin account? can you try run qnap finder using admin to see if that makes any difference? or possibly reinstall qfinder? Only other thing i can think of is the ethernet cable has a issue. I'm assuming that your qnap leds are all indicative that it is powered on and without issue? usually if there is a serious issue it would blink different led colors or make beeping noises. You can also try reboot your pc, your router and switch, and nas. Any firewalls on your pc is blocking access to the nas? one possible scenario. ![]() ![]() In the past when i use dhcp and router went down then came back up, it usually sometimes resulted in issues for me.Īnother thing is probly firewall. I recommend you set a static ip in QTS so that the qnap nas ip remains fixed and unaffected if the router goes down. Also how is your qnap getting it's ip? does it have a static ip setup? or did you do a DHCP?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |